Lee Reloading

 

	Reloading Kits
	Presses & Accessories
	Pro 1000 & Load Master
	Powder Handling
	Dies, Shellholders etc.
	Case Conditioning Tools & Priming Tools

 

LEE - Dies, Shell Holders Etc

Lee Pistol Dies
We use a solid carbide insert, ground to a special contour that does not leave the objectional belt mark on the case, common to ordinary carbide dies. With a carbide sizer, no case lube is needed, and you don't even have to clean your cases. No need for a taper crimp die, plus better accuracy with Lee Dies. Taper crimp dies are used to correct the problems caused by the improper expanding plug design or adjustment. They distort the bullet shank and reduce accuracy. Because the Lee Expander flares the minimum amount, consistent with easy bullet insertion, all of the flare is removed with the bullet seating die, thus eliminating the need for a taper crimp die. 3 die carbide set with shell holder + dipper and chart (please specify pistol caliber in comment box on order form for below)  NZ$105 (incl. GST) Quantity: 1 2 3 5 10 3 die steel set non carbide with shell holder etc (please specify pistol caliber in comment box on order form for below)  NZ$85 (incl. GST) Quantity: 1 2 3 5 10
Lee PaceSetter Die Sets
Includes: * FULL LENGTH SIZER * BULLET SEATER & ROLL CRIMPER * FACTORY CRIMP DIE * BUILT IN STUCK CASE REMOVER * LONG GUIDED EXPANDER * SHELL HOLDER * POWDER DIPPER * LOAD DATA AND INSTRUCTIONS Best Internal Finish in the Industry All Lee dies are machine honed to the smoothest possible finish. Don't confuse this with the surface polish used by most manufacturers. A polish simply makes a shiny surface. It's like trying to sand wood without backing under the sandpaper. The surface in Lee dies is progressively honed to a fine finish with no waves or ripples. Pacesetter 3 die set common calibres with factory crimp die  NZ$103 (incl. GST) Quantity: 1 2 3 5 10 Pacesetter (3 die) and Limited Production (2 Die) sets (OTHER than those listed above, please specify)  NZ$107 (incl. GST) Quantity: 1 2 3 5 10		Lee PaceSetter Dies include the exclusive Lee Factory Crimp Die to produce factory-like ammunition with improved utility and accuracy. The die set also includes a conventional bullet seater and roll crimper. You can choose the type of crimp you desire. These dies are your best buy. They also include a shell holder, powder dipper, load data and are packed in the nicest storage box ever designed. These extras represent an $18.00 value. Most of these extras are unavailable at any price from other suppliers. These are the most copied dies in the world. Every die comes with a written lifetime warranty, 2 year guarantee and guarantee of accuracy or your money back! This set is recommended for assembling ammunition for hunting purposes as the finished rounds chamber easily and can withstand rough handling of the firearm action.
Lee RGB Series Dies
Compare to other brands costing twice as much and you'll recognize what a fantastic bargain they are. We offer these only to show that when you buy Lee Dies- without all the extras Lee customers have come to expect- the price is significantly lower, yet the quality is the best. Our tolerance is 50% less than the advertised amount of a popular and expensive brand. We guarantee these dies are better than any other brand. These dies are a Really Great Buy. They cost less, because like other die makers, we left out the extras which are included in our PaceSetter™ dies. RGB Series 2 Die Rifle Sets  NZ$55 (incl. GST) RGB (Really Great Buy) Series dies in the GREEN BOX are exactly the same dies as Lee's standard red box. These sets DO NOT have the factory crimp die, shell holder, powder dipper or load data. You get the 2 die set only. Quantity: 1 2 3 5 10
Lee Collet Dies
Common Calibres are: (222, 223, 22/250, 243, 6.5x55, 270, 7mm/Mag, 7.62x39, 30-30, .308, .30-06, .303, 8mm please specify in comment box on order form) Die set includes: Collet neck sizing die, dead length bullet seating die, shell holder, powder measure, charge table and storage box. This set is designed for assembling the most accurate ammunition, but is not recommended for hunting rounds as the case is neck sized only and the bullet is not crimped in case. Collet Series 2 die set includes most accurate neck sizer  NZ$88 (incl. GST) Quantity: 1 2 3 5 10 Deluxe Collet 3 Die series (Includes a Full Length sizer)  NZ$105 (incl. GST) Quantity: 1 2 3 5 10 Special 3 die set for straight walled rifle cases  NZ$78 (incl. GST) Quantity: 1 2 3 5 10 M-1 Carbine.  Special set (Tungsten Carbine)NZ$88 (incl. GST) Quantity: 1 2 3 5 10		There is no loading system that will load more accurate ammunition than Lee Collet Dies. We guarantee it in writing with every set. No one but Lee has ever dared to make a guarantee like this "Smallest group size or your money back." A collet squeezes the case neck against a precision mandrel for a perfect fit with minimum run-out. No lube case is needed. Cases last ten times longer, so the savings on only 35 cases will pay for the dies. Maximum accuracy is usually achieved by seating the bullet out far enough to touch or almost touch the rifling. This provides the shot start pressure normally supplied by the crimp. That's why a dead length bullet seater is included to complete the most accurate reloading system ever made. These dies size only the neck to preserve the perfect fit of fire forming. Only reload cases that have been fired in your gun. Not recommended for autoloaders, slide or lever action guns.
Lee Dies
Factory Crimp die - Rifle NZ$45 (incl. GST) (please specify caliber in comment box on order form for below)  Quantity: 1 2 3 5 10 Lee Factory Crimp Die: * Crimps the bullet in place more firmly than any other tool. * It is impossible to buckle the case as with regular roll crimp dies. * Trim length is not critical. * Tests demonstrate that even bullets which have no cannelure will shoot more accurately if crimped in place with the Lee Factory Crimp Die. Factory ammunition is often more accurate and better able to withstand rough handling because the bullet is firmly crimped in place. A firm crimp improves accuracy because pressure must build to a higher level before the bullet begins to move. This higher start pressure insures a more uniform pressure curve and less velocity variation. Even powder selection is less critical. Until now, handloaders seated the bullet to touch the rifling to achieve similar results. This is not always possible nor desirable. The Lee Factory Crimp Die is included at no extra charge with Lee PaceSetter Dies. It's just another added value that only Lee Dies offer.
Carbide Factory Crimp die - Pistol NZ$74 (incl. GST) Quantity: 1 2 3 5 10 A carbide sizer sizes the cartridge while it is being crimped so every round will positvely chamber freely with factory like dependability. The adjustig screw quickly and easily sets the desired amount of crimp. It is impossible to buckle the case as with a conventional bullet seating die. Trim length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered. Revolver dies roll crimp with no limit as to the amount. A perfect taper crimp is applied to auto-loader rounds. The crimper cannot be misadjusted to make a case mouth too small to properly head-space. A firm crimp is essential for dependable and accurate ammunition. It eliminates the problems of poor ignition of slow burning magnum powders.		Taper crimp die (Available in Pistol cals +22 & 30 cal Rifle)  NZ$40 (incl. GST) Quantity: 1 2 3 5 10 The Lee Taper Crimp Dies is hardend steel designed to overcome crimp problems caused by poor die design. These dies offer little or no advantage when used wth 1986 or newer Lee Dies as the crimp angle is already modified taper crimp. Jacketed bullets must have a crimp groove.
Collet Neck Sizing Die NZ$66 (incl. GST) (please specify caliber in comment box on order form for below)  Quantity: 1 2 3 5 10 Carbide sizer die for pistols  NZ$74  (incl. GST) Quantity: 1 2 3 5 10		Die Lock Rings (Universal - Set of three) NZ$19 (incl. GST) Quantity: 1 2 3 5 10
Shell Holders
Shell holder for Autoprime/Hand Primer (please specify caliber in comment box on order form for all below)   NZ$11 (incl. GST) Quantity: 1 2 3 5 10 Auto Prime Shell Holder Set   NZ$45 (incl. GST) Set of eleven shell holders, packed in a sturdy plastic box, fits over 120 different cartridges. Quantity: 1 2 3 5 10 Shell holder for Press (fits all standard presses) "R" Series NZ$14 (incl. GST) Quantity: 1 2 3 5 10 Press Shell Holder Set  NZ$53 (incl. GST) Set of eleven shell holders, packed in a sturdy plastic box, fits over 120 different cartridges. Quantity: 1 2 3 5 10