|
All
prices are in New Zealand Dollars with 15% GST included.
Overseas customers
are not liable for GST, divide NZ$ by 1.15 and then use the below Currency Converter:
|
|
|
|
|

|
Acculine
Case Trimmer NZ$132 (incl.
GST)
Includes
Pilot Multi-Pack (22, 24, 27, 28, 30, 9mm, 35, 44, 45A).
Made in USA
T rims all rifle and pistol cases from .22 through .458 Winchester Magnum. Uses standard shellholder to position the case and incorporates standard Lyman cutter heads and pilots mounted on a centerless ground shaft adjustable for depth of cut. Can be bench mounted, held by C-clamps, or held in a vise.
|
|
Neck
Turner NZ$75 (incl.
GST)
For both Lyman's Universal Trimmer and AccuTrimmer. Provides the user with a simple-to-operate tool that guarantees neck wall thickness and outside neck diameter. Essential for case reforming. Improves accuracy. Adjustable cutter (for length of cut and rate of feed) removes minimum brass to attain uniformity. Cutter blade can be adjusted to any diameter from .195" to .405". Comes with two extra cutting blades. Mandrels from .22 to .375. Includes six mandrel Multi-Pack (for .22, .243, .25, .270, 7mm, and .30 calibers). (Not adaptable to Power Trimmer.) Replacement parts and additional mandrels also available. Shown on Lyman AccuTrimmer.
The
Lyman Outside Neck Turner is designed for use on the Lyman Acculine
Case trimmer. With 6 Mandrels.
|
| |
|
|
|
Digital
Powder System III 230v NZ$790 (incl.
GST)
Lyman's
Revolutionary 1200DPS Digital Powder System combines a precision
electronic Powder Scale and an automatic Powder Dispenser into
one easy to use unit. The DPS remembers
up to 20 of your favorite loads and you can easily recall any
of them by Cartridge, Specific Powder and Weight. No Powder Calibration
(Flow Rate) is required, just select the one you want and start
dispensing powder. It dispenses powder quickly and is accurate
to + or - 1/10 grain. It can be used as a complete Dispensing
System, just a scale or as a Scale and a Powder Trickler. The
1200DPS is fast, accurate and affordable. Note: not for use with
black powder.
|
|
Super
Moly Bullet Finishing
Accessory Pack
NZ$145 (incl.
GST)
Everything
you need to Super Moly Coat bullets. All you add is the tumbler!
The two heavy duty bowls will fit the Lyman 600 and1200
tumblers and most other brand tumblers of similar size. The kit
contains two heavy duty long lasting bowls, six ounces (6oz) of
Superfine Grade Moly, Moly plating media, and fine finishing media.
This kit will coat many thousands of bullets. Only a small amount
of Special Superfine Grade Moly is needed for a durable, high-gloss,
moly coated finish. Coating instructions are included.
|
| |
|
|
|
Flash
Hole Uniforming Tool NZ$29 (incl.
GST)
During
case manufacture, burrs are oftenraised
around the primer flash hole from punching operations and primer
flash hole uniformity can be affected.
The Lyman Flash Hole Uniformer will remove these burrs and standardize
the length of the flash hole, allowing a more uniform flash to
ignite the powder charge thus improving accuracy. 
The cone adapter is adjustable to fit various length rifle and
pistol cases from .22 to .45 caliber. The rod unit can be mounted
in the Lyman multi-purpose wooden handle or into the bench mounted
Lyman utility crank and base.
|
|
Primer
Pocket Uniformer
NZ$49 (incl.
GST)
The
Myman Primer Pocket Uniformer Tool is designed to cut primer pockets
to a uniform depth and at the same time squares the seating surface
for the anvil of the primer that can produce more consistent ignition
and lead to greater accuracy. Primers are constructed so that
the anvil protudes slightly from the open end of the primer cup.
This is necessary so that the anvil will rest firmly on the bottom
of the primer pocket. When the firing pin strikes the primer,
the impact sensitive compound inside the primer is crushed between
the anvil and cup causing the compound to ignite. Variations in
the depth or configuration of the primer pocket, or in the primer
seating operation itself, can alter the effects of the firing
pin blow. This, in turn, effects the ignition of the primer and
may affect the accuracy of the cartridge.
Comes in Small or Large.
|
| |
|
|
|
Electronic
Digital Trigger Pull Gauge NZ$106 (incl.
GST)
The
new Lyman Trigger Pull Gauge is designed to be the fastest and
most accurate Trigger Pull Gauge available on the market. Unlike
other gauges, there are no weights or sliding pointers to contend
with. Simply place the gauge on the trigger and pull!This instrument will accurately record the results, as you can
take multiple readings and then take the average weight for the
string at the touch of a button! This state of the art instrument
is a must for any shooter or gunsmith!
* 0-12
Pound Range
* 1/10
Ounce Accuracy
* 10
Pull Averaging
* Reads
in Kilograms
* Large
Digital LCD Display
* Strain
Gauge Technology |
|
Turbo
1200 Tumbler w/media NZ$225
(incl.
GST)
The
new 1200 Classic features a completely redesigned base and drive
system which was developed after years of studying and evaluating
tumbler performance. The 1200 drive system has a beefed up suspension
system and built in exciters for better tumbling action
and faster case cleaning. The new drive system has improved air
flow for cooling and guaranteedlonger
motor life. Combined with our new Anti-Rotation Pad Mounts the
1200 Classic runs smoother, quieter and better than ever before.
The Turbo 1200 Tumbler comes with european plug, so needs an adapter
to plug in to New Zealand plug sockets.
Media
Charge (lbs): STD 2
#.38 Spec.Cases: 350
BowlCapacity: 1
Gal.
BowlSize(Dia.): 10"
Media
Included |
|
| Copyright © 2012 Hunting and Outdoor Supplies. All Rights Reserved. |
Updated February 2012 |
|